Volume 1  Number 1 (2011)

CONTENTS

Feasibility and Sensitivity Robust Optimum Design by Method of Transmitted Variation
pp. 1-8
Authors: Kelkar Satej Sudhakar

Analysis of Bearing Performance Characteristics for Partial Arc Journal Bearings with Bearing Design System Program
pp. 9-15
Authors: Challa Jayaramulu, K.C.B. Raju and K.N. Rao

Review on Modelling Transmission Noise in Geared Systems 
pp. 17-23
Authors: C.V.S.R. Subrahmanyam

Synthesis of Nano-Sized Hydroxyapatite in Different Forms from Biological Waste Material: The Dead Snail Shells
pp. 25-34
Authors: M. Dasgupta Adak, A.K. Chattopadhayay and K.M. Purohit

Energy Management and Conservation
pp. 35-43
Authors: K. Natarajan and D. Vijayakumar

Corner Compensation Strategy in WEDM for Enhanced Profile Accuracy
pp. 45-52
Authors: S. Sarkar, S. Mitra and B. Bhattacharyya

Perovskite Doped and ��-Irradiation Induced Electrical Properties of Composite Film
pp. 53-58
Authors: Girish Mukundrao Joshi

Anti T7 Immobilized Single Conducting Polypyrrole Nanowire for Phage Detection
pp. 59-63
Authors: Dhammanand J. Shirale

Enhancing Competitiveness of Foundry SMEs through Design for Changeovers (DFC): A Case Study
pp. 65-78
Authors: Bikram Jit Singh and Dinesh Khanduja

Genetic Algorithm based Pareto Optimization of Electro Discharge Machining of Titanium Nitride-Aluminium Oxide Composite
pp. 79-86
Authors: S. Mitra and S. Sarkar

Tolerance Analysis for a Reciprocating Air Compressor Assembly 
pp. 87-100
Authors: Atul Kumar and Krishan Kumar

Study of Formation of Defects in Joints and their Remedies in Semiautomatic Orbital TIG Welding
pp. 101-108
Authors: N. Arunkumar, D. Ananthapadmanaban and S. Balaji

Effect of Cryogenic Treatment on Wear of Carbide Inserts in CNC Machining
pp. 109-115
Authors: Rupinder Singh and Kamaljit Singh

Sliding Wear Performance of Detonation Spray Al2O3, TiO2 and Hydroxyapatite Hybrid Coatings
pp. 117-127
Authors: Harpreet Singh, Rahul Chhibber, Harpreet Singh and Sanjeev Bhandari

Modeling and Simulation of Metal Cutting Processes
pp. 129-138
Authors: Girish Kant and K.S. Sangwan

Prediction of Metal Removal Rate in Electrical Discharge Machining using Artificial Neural Network
pp. 139-148
Authors: Anand K. Patel and H.R. Prajapati

Effect of Powder Mixed Dielectric Fluid on Surface Modification during Electrical Discharge Machining (EDM): A Review
pp. 149-158
Authors: Anand K. Patel, H.K. Raval and H.R. Prajapati

Friction Stir Welding: A Review
pp. 159-167
Authors: Deepak Pandey

Simulating Manufacturing Plant using Manufacturing-Oriented Simulator
pp. 169-178
Authors: Anuj Nautiyal and Amir Sheikh

An Experimental Study of Flow through a Dump Combustor Model with Inlet Swirl
pp. 179-187
Authors: Abdur Rahim

Design of Advanced Solar Water Heater
pp. 189-199
Authors: K. Sarath Kumar, R. Siva Kumar and M. Govindaraj

Design of Shell and Tube Heat Exchanger using Ant Colony Optimization Technique
pp. 201-215
Authors: J.V. Sindha and R.V. Rao

Thermal Analysis of an Activated Carbon-Ammonia Adsorption Refrigeration System
pp. 217—228
Authors: Anirban Sur and Randip K. Das

Performance Improvement of Centrifugal Slurry Pump using Additives
pp. 229-238
Authors: Sunil Chandel, Singh S.N. and V. Seshadri

Analysis of Main Journal Bearing in High Specific Power Diesel Engine
pp. 239-247
Authors: K. Jagannathan and K. Srinivasan

Disc Break Friction Materials: A Review
pp. 249-258
Authors: Pradnya Kosbe and Chittaranjan More

 [UP]